This object is in archive! 

Zipato 4 in 1 Multisensor - BIT's meaning

Atilla Ö. shared this question 7 years ago
Need Answer

Hello,

I have Zipato 4 in 1 Multisensors.

On the Configuration section, there are BITs for settings. I could not find enough/understandable explanation form installition guides (V1.2 , V1.3, V1.4, V1.5).

Could you please give information?

Operation mode : BIT 1-2-3-4-5

Multisensor function switch : BIT 0-1-2-3-4-5

Customer switch : BIT 1-2-3-4

Also DIP switch : 1-2

Replies (4)

photo
1

Hello, To understand the configuration, you must transform the value into binary. This makes it possible to count with a number of several BITs. The value is encoded in 8 bits: bit 0 to 7

Example: For parameter 5 (mode operation) If the value is 28 or 00011100

bit0=0 Bit1=0 bit2=0 bit3=1 bit4=1 bit5=1 bit6=0 bit7=0


For parameter 6 (multisensor switch function) If the value is 8 or 00001000

bit0=0 Bit1=0 bit2=0 bit3=0 bit4=1 bit5=0 bit6=0 bit7=0


see the manual for parameter 5 or 6.


For the DIP switch, it is the micro switch that is on the circuit of Zipato 4 in 1. There is 2 switch M1 and M2 with ON or OFF position.

photo
1

This was very useful Arguimbau, but where can I find the value? In the attached screenshot you can see the configurations of a Zipato Multisensor Quad. Parameter 5 / Configuration option 5 is the the section called "OPERATION MODE". Here I find Bit 1 to 5, but I can´t find the value corresponding to a 8 bit streng. Where do i find this?

photo
1

Hello,

in the manual of the PST02 there is the programming table of the configuration 5.


bit 0 not used

bit 1 test mode or normal mode

bit 2 disable door / windows function

bit 3 fahrenheit / celsius

bit 4 disable illumination report

bit 5 disable temperature report

bit 6 not used

bit 7 disable the back key release into test mode


the value of each bit is 0 or 1

if you only have bit 1 to 5 you have to add bit 0, 6 and 7.


if :


bit 0 = 0 not used

bit 1 = 0 normal mode

bit 2 = 0 door / windows function is enable

bit 3 = 1 celsius enable

bit 4 = 1 illumination report disable after event triggered

bit 5 = 1 temperature report disable after event triggered

bit 6 = 0 not used

bit 7 = 1 disable the key release on test mode


the value of parameter 5 is 10111000 or 184

the bit 0 is at right and the bit 7 is at left. sorry, but I reversed before.

photo
1

Thanks. I just don´t understand how I actually program this. The only thing I understand I can do under configuration is to toggle these green/grey bit-buttons on and off (see attached). I interpret green to be on, but I´m not sure. When I klick Send or Retrieve I get a number in return. Eg. how do I change bit3 from 0 to 1?

photo
2

Hello,


To pass bit 3 from 0 to 1, use the BIT 3 button on the interface: green = 1 gray = 0


You will enter the decimal value "184" of the complete configuration of the "Operating Mode"


10111000 in binary = 184 in decimal


use this address to convert binary files to decimals


http://sebastienguillon.com/test/javascript/convertisseur.html


enter a new value


Parameter = 5


Size = 1


Value = 184


and uses the send button

photo
Leave a Comment
 
Attach a file
You can't vote. Please authorize!
You can't vote. Please authorize!
You can't vote. Please authorize!
You can't vote. Please authorize!
You can't vote. Please authorize!
You can't vote. Please authorize!