Fibaro Heat Controller with Virtual Thermostat PRO
Known
Hi Guys,
I've started installing Fibaro Heat Controllers (TRV) with temp sensors. They Install fine and show up as two temperature devices, a set-point temperature and room temperature. I've also created a virtual switch per device to be operated by the virtual thermostat.
My problems occur when I create the thermostat. I've tried every permutation of input/output setting (including adding the virtual switch as an output each time) but cannot get it to operate the switch. I can move the slider on the thermostat and this opens and closes the valve... but no switch action = no heat
Hope someone can point me in the right direction
Many thanks
Sean
You can't vote. Please authorize!
You can't vote. Please authorize!
You can't vote. Please authorize!
No connection
Real-time notifications may not work
Raise a Support Ticket. Perhaps the TRV has not have a descriptor.
Raise a Support Ticket. Perhaps the TRV has not have a descriptor.
Thanks Attila, have done now
Thanks Attila, have done now
Hi Sean,
I am encountering the same situation, the only difference is that I do not have the temperature sensors (from Fibaro).
Do you have any feedback from Support ?
My guess is that currently this valves are not fully supported on our Zipato systems. I tried to create a rule (see attachment), but I had partial results:
- Virtual Thermostat Pro is switching off Fibaro Heat Valve
- Set point does not work properly. I had tried several rule configurations but with unsuccessful results :(
regards,
Val
Hi Sean,
I am encountering the same situation, the only difference is that I do not have the temperature sensors (from Fibaro).
Do you have any feedback from Support ?
My guess is that currently this valves are not fully supported on our Zipato systems. I tried to create a rule (see attachment), but I had partial results:
- Virtual Thermostat Pro is switching off Fibaro Heat Valve
- Set point does not work properly. I had tried several rule configurations but with unsuccessful results :(
regards,
Val
I didn't get much help from support other than advice to upgrade my firmware which had no effect. I did however get it all working! So, my method...
I created a simple virtual switch for each room and a rule that "If A or B or C = On, set Boiler On, else set Boiler Off"
Then setup each Virtual Thermostat Pro with the Fibaro stat as an input AND output, the extra temp sensor as a Temp input and the virtual switch for that room as an output.
Then I discovered that the Stat needed to be set to AUTO... Then my virtual switch started to turn On and Off with the slider! YAY!
Then in "Device Browser" I clicked on Settings for each stat and set up a temperature timetable for each room.
Good Luck, I found it all very trial and error... but I got there :)
Sean
PS the extra temp sensor is useful for better accuracy, but I don't think is really necessary.
I didn't get much help from support other than advice to upgrade my firmware which had no effect. I did however get it all working! So, my method...
I created a simple virtual switch for each room and a rule that "If A or B or C = On, set Boiler On, else set Boiler Off"
Then setup each Virtual Thermostat Pro with the Fibaro stat as an input AND output, the extra temp sensor as a Temp input and the virtual switch for that room as an output.
Then I discovered that the Stat needed to be set to AUTO... Then my virtual switch started to turn On and Off with the slider! YAY!
Then in "Device Browser" I clicked on Settings for each stat and set up a temperature timetable for each room.
Good Luck, I found it all very trial and error... but I got there :)
Sean
PS the extra temp sensor is useful for better accuracy, but I don't think is really necessary.
Hi Sean,
I've also wanted to buy the fibaro temp sensor but at the moment it is not available on the german market.
I think we have similar approaches concerning the virtual switch / room and the necessary rule. Could you please attach a screenshot with your rule and another with the device settings for the virtual thermostat pro ?
How is the battery life in your case, I am not very satisfied with what I see.
In my case in almost 2 weeks I got a discharge of 37%....
Hi Sean,
I've also wanted to buy the fibaro temp sensor but at the moment it is not available on the german market.
I think we have similar approaches concerning the virtual switch / room and the necessary rule. Could you please attach a screenshot with your rule and another with the device settings for the virtual thermostat pro ?
How is the battery life in your case, I am not very satisfied with what I see.
In my case in almost 2 weeks I got a discharge of 37%....
Replies have been locked on this page!