This object is in archive!
How can we manually change Danfoss Living Connect temperature ?
Need Answer
I just started with Zipabox and 4 Danfoss valves 014G0012.
I have all setup correctly as they are all visible on MyZipato Dashboard as Meters.
Now I would like to manually change the temparature set on the valve from the Zipato interface. How can I do that ??
I cannot used Climate option as I don't have any thermometers in the same room and thermometer in put is mandatory.
Thanks for help
The same question You can't vote. Please authorize!
You can't vote. Please authorize!
You can't vote. Please authorize!
You can't vote. Please authorize!
No connection
Real-time notifications may not work
Then try to use a scheduler in the when as a trigger.
Have one scheduler fort the start time and an other for the stop time.
And at start set TEMP=18 and at stop set TEMP=20
One rule for start and one rule for stop.
Then try to use a scheduler in the when as a trigger.
Have one scheduler fort the start time and an other for the stop time.
And at start set TEMP=18 and at stop set TEMP=20
One rule for start and one rule for stop.
Yes, scheduler would be an option if I want to schedule temperature changes..
But if I just want to increase by a few degrees the temprature right now I don't want to create a rules for that... I looking for a simple equivalent of the up and down button of the Danfoss valve.
Yes, scheduler would be an option if I want to schedule temperature changes..
But if I just want to increase by a few degrees the temprature right now I don't want to create a rules for that... I looking for a simple equivalent of the up and down button of the Danfoss valve.
A schedular rule can look like this...
if you make sure to sync the schedular-event-time with the if-time, you can have all in one rule...
ops, sorry wrong answer ;-)
don't think there is a good up/down-virtual device to use for this.
One way to do it could be to use a "virtual level control" to input the temerature (in %)
But that will just show 0% - 100% so you have to recalculate before you set the temp.
then use a virtual meter to present the calculated value, so you kan see what temp that given procent value is.
Create a Rule that triggers on the change of %level
Recalculate % to a temparature value
set METER=value
set DANFORS=value
Then you have something that you can use to change and see the set value.
But doesn't the DANFORS have that functionality????
(I don't know I don't have any thermostate)
A schedular rule can look like this...
if you make sure to sync the schedular-event-time with the if-time, you can have all in one rule...
ops, sorry wrong answer ;-)
don't think there is a good up/down-virtual device to use for this.
One way to do it could be to use a "virtual level control" to input the temerature (in %)
But that will just show 0% - 100% so you have to recalculate before you set the temp.
then use a virtual meter to present the calculated value, so you kan see what temp that given procent value is.
Create a Rule that triggers on the change of %level
Recalculate % to a temparature value
set METER=value
set DANFORS=value
Then you have something that you can use to change and see the set value.
But doesn't the DANFORS have that functionality????
(I don't know I don't have any thermostate)
there is no way to manually set the danfoss units... this should be implemented instead of a workaround with rules and everthing.
Your idea is nice but should not be required in my opinion... how hard could it be to make a input field at thermostats and danfoss units?
there is no way to manually set the danfoss units... this should be implemented instead of a workaround with rules and everthing.
Your idea is nice but should not be required in my opinion... how hard could it be to make a input field at thermostats and danfoss units?
I don't think that an input field is needed. Two buttons "+/-" should be enough. Exactly as it is done on the Dafoss valve.
I don't think that an input field is needed. Two buttons "+/-" should be enough. Exactly as it is done on the Dafoss valve.
hi, for myself i have the same config as you, and i use the climate widget, to bypass the need of a thermostat, i create a virtual thermometer and user it in thermometerendpoint with custom as function.
hi, for myself i have the same config as you, and i use the climate widget, to bypass the need of a thermostat, i create a virtual thermometer and user it in thermometerendpoint with custom as function.
I also tried that, but when I create a virtual thermometer as new device of type "Virtual meter" it never appears in thermometer endpoint in Climat config screen.
How did you do it ?
I also tried that, but when I create a virtual thermometer as new device of type "Virtual meter" it never appears in thermometer endpoint in Climat config screen.
How did you do it ?
Replies have been locked on this page!